Click the Exhibit button.

Referring to the diagram shown in the exhibit, what will happen if PDU-B fails?

Exhibit:

A. Both Node A and Node B will remain online and all disk shelves will remain online.

B. Both Node A and Node B will remain online, but all disk shelves will immediately lose power and become inaccessible.

C. Both Node A and Node B will immediately lose power and become inaccessible.

D. Node A will immediately lose power and become inaccessible. Node B will remain online.

You are asked to migrate a SAN LIF to a node that was recently added to your cluster. The following CLI command was provided to you to complete the migration:

network interface modify -vserver svm1 -lif lif1 home -node cl01-04 -homeport6a

Which step is missing?

A. All hosts connecting to the controller through lif1 must be shut down.

B. The LIF must first be added to a portset.

C. Your zoning must be updated on the upstream switch.

D. The LIF must be put in a status-admin down state.

You are verifying multipathing from the host to the storage controller. Which three components should you verify? (Choose three.)

A. Verify that all switch ports connected to the hosts and storage devices are online using the vendor's GUI.

B. Verify that both FC HBA ports in the host are online using the HBA vendor's GUI.

C. Verify that the FC HBAs WWNN's are in the igroup in the SVM.

D. Verify that the SVM's LIFs being used for multipathing are attached to the correct same physical FC port.

E. Verify that the storage controller FC target ports status are online with the switch port showing the FC switch to which they are connected.

Which two flags would you use to enable NetApp thin provisioning on a LUN? (Choose two.)

A. -space-reserve enabled -space-allocation enabled

B. -space-reserve enabled -space-allocation enabled

C. -space-reserve disabled -space-allocation disabled

D. -space-reserve disabled -space-allocation enabled

Which objects reside inside an igroup?

A. host initiators

B. LUNs

C. qtrees

D. volumes

Which command enables the FC protocol on clustered Data ONTAP?

A. vserverfpolicy enable -vserver -policy name -sequence number

B. vserverfcp create -vserver -status -adain up

C. node run node fcadmincongig -e

D. vserveriscsi create-vserver -target -alias

A new server has been installed in your environment, but it is unable to see its NetApp boot LUN. You have narrowed the problem down to the zoning on your Cisco switch which has the following configuration:

zone name z_NetAppvsan 400 memberpwwn 20:00:00:25:b5:c0:ff:ee memberpwwn 50:0a:09:84:8d:7c:51:d5 zoneset name zs_NetAppvsan 400 memberz_NetApp zoneset activate name zs_NetAppvsan 400

What is the problem with your zoning configuration?

A. The member does not reference the VSAN.

B. The zone and zoneset names do not match.

C. The zoneset was improperly activated.

D. The PWWN for your NetApp LIF is incorrect.

A Windows 2012 Server has a 1 GB thin-provisioned LUN in a 10 GB thin-provisioned volume. After copying a 500 MB file to the LUN, you observe the LUN using 500 MB of space in the volume. After deleting the 500 MB file, you observe the LUN is still using 500 MB of space in the volume.

Which two steps are required to reclaim the space? (Choose two.)

A. Press Optimize in the Windows Defragment and Optimize Drives utility.

B. Enable space-allocationon the LUN.

C. Run TRIM on the host.

D. Empty the Recycle Bin on the host.

A customer is experiencing slower than expected performance on a database connected to an iSCSI LUN. They are surprised that performance has decreased even though they have upgraded from a 1 GB to a 10 GB switch.

What are three causes for this problem? (Choose three.)

A. Spanning Tree is incorrectly configured on the cluster nodes.

B. There is a faulty cable or SFP in the data path.

C. There is an MTU mismatch between the hosts, controllers, and switch.

D. Flow control is incorrectly set on either the host or controllers.

E. Routing is not set up between the iSCSI and cluster networks.

What does Selective LUN Mapping (SLM) do?

A. It automates igroup creation.

B. It allows the node and its HA partner to create zones on the SAN fabric to automate LUN mapping.

C. It makes a LUN accessible only through paths on the node owning the LUN and its HA partner.

D. It allows the administrator to automatically create LUNs using SnapDrive for Windows and SnapDrive for UNIX.