You are logged in to Leaf 1. When examining the routing table, you notice that you have no routes from Leaf 2.

Referring to the exhibit, which two commands would you use to troubleshoot the problem? (Choose two.)

A. From Leaf 2, issue the show route advertising-protocol bgp 172.16.1.2 command.

B. From Spine 1, issue the show route advertising-protocol bgp 172.16.1.1 command.

C. From Spine 1, issue the show route advertising-protocol bgp 172.16.1.2 command.

D. From Leaf 1, issue the show route receive-protocol bgp 172.16.1.1 command.

After configuring an IP fabric using EBGP as your routing protocol, you notice that not all of the routes are showing up in the routing tables. You have verified that all adjacencies have formed, and that all policies are in place and configured properly.

In this scenario, which statement is true?

A. The routers have not been configured with the multipath multiple-as parameter.

B. The routers have not been configured using the add-path parameter.

C. The routers have not been configured using the bfd-liveness-detection parameter.

D. The routers have not been configured using the multihop parameter.

You are implementing perimeter security for your data center. You need to inspect all traffic at Layer 7 and ensure the failure of a port or device will not result in an interruption to traffic flows.

In this scenario, which design would satisfy these requirements?

A. SRX using LAG

B. MX with MC-LAG

C. QFX Virtual Chassis

D. SRX chassis cluster

Which two combinations are supported when configuring a Virtual Chassis Fabric? (Choose two.)

A. two spine nodes and 28 leaf nodes

B. four spine nodes and 20 leaf nodes

C. four spine nodes with 16 leaf nodes

D. two spine nodes and 16 leaf nodes

What is the purpose of the command shown in the exhibit?

A. to stop the transmission of transit multicast traffic when there are no interested receivers attached to a remote VTEP.

B. to disallow IGMP requests for the group 239.0.0.1 from hosts attached to the local VTEP.

C. to disable the multicast group 239.0.0.1 across the entire VXLAN.

D. to stop the reception of transit multicast traffic when there are no interested receivers attached to the local VTEP.

Which two statements describe EVPN-based VXLAN implementations? (Choose two.)

A. The movement of a virtual host requires a manual reconfiguration of the VTEP.

B. The movement of a virtual host results in the dynamic remapping of the VTEP.

C. MAC addresses are learned using multicast flooding.

D. MAC addresses are propagated using BGP updates.

Which protocol is used between VCF member devices to create a loop-free topology?

A. LLDP

B. MSTP

C. RSTP

D. VCCP

You are creating a new EVPN and are asked to selectively accept certain MAC advertisement routes from your EVPN peers using VXLAN encapsulation.

Which statement is correct in this scenario?

A. You can use MAC filtering to filter out unwanted routes.

B. You can use VRF import policies and route distinguisher values to filter out unwanted routes.

C. You can use VRF import policies and community values to filter out unwanted routes.

D. You can use firewall filters to filter out unwanted routes.

Which two statements are true about Virtual Chassis? (Choose two.)

A. The request virtual-chassis mode fabric reboot command will set the Virtual Chassis to fabric mode with similar devices.

B. The request virtual-chassis mode fabric reboot command will set the Virtual Chassis to mixed mode.

C. By default, Junos switches are in a non-mixed mode Virtual Chassis.

D. By default, Junos switches are in mixed mode Virtual Chassis.

Referring to the exhibit, what would cause the problem on VCP 0/50?

A. The VCP has been disabled through configuration.

B. The remote side is not configured as a VCP.

C. VCP 0/50 is configured as a network port.

D. The port is missing the interface hardware.