When setting up VoIP, you decide that you want to use LLDP. LLDP is enabled by default and LLDP Transmit Management Information and Notification modes are enabled.

What additional steps need to be performed?

A. Enable ISDP and enable LLDP-MED confignotification

B. Disable ISDP and enable LLDP-MED confignotification

C. Enable ISDP and disable LLDP-MED confignotification

D. Disable ISDP and disable LLDP-MED confignotification

Switch-1(config)# interface tengigabitethernet 1/0/1 Switch-1(config)# switchport mode access Switch-1(config)# switchport trunk allowed vlan 10, 20 Switch-1(config)# Switch-1(config)# interface tengigabitethernet 1/0/3 Switch-1(config)# switchport mode access Switch-1(config)# switchport access vlan 10

Switch-2(config)# interface tengigabitethernet 1/0/2 Switch-2(config)# switchport mode trunk Switch-2(config)# switchport trunk allowed vlan 10, 20 Switch-2(config)# Switch-2(config)# interface tengigabitethernet 1/0/6 Switch-2(config)# switchport mode access Switch-2(config)# switchport access vlan 20

A network administrator is troubleshooting why Host 1 cannot communicate with Host 2.

Based on the switch output shown in the exhibit, what is the reason for the communication issue?

A. Port Te1/0/1 on Switch-1 is configured incorrectly

B. Port Te1/0/2 on Switch-2 is configured incorrectly

C. Port Te1/0/3 for Host 1 is configured incorrectly on Switch-1

D. Port Te1/0/6 for Host 2 is configured incorrectly on Switch-2

What are key features of the Dell EMC N4064 or N4064F switches?

A. Up to 640 Gbps switch fabric capacity and hot swap expansion module support for dual QSFP+ (8 x 10GbE)

B. Up to 1.0 Tbps switch fabric capacity and up to 48-line rate 10GbE ports per switch

C. Up to 1.2 Tbps switch fabric capacity and up to 64-line rate 10GbE ports per switch

D. Up to 48-line rate 10GbE ports per switch and hot swap expansion module support for dual QSFP+ (8 x 10GbE)

A switch interface has been properly configured for static port security with one defined allowable MAC address. However, when the network administrator plugs a switch into that port, multiple devices are still allowed access to the network. Where must port security also be enabled to have an effect?

A. Enabled globally on the switch

B. Enabled on all attached devices

C. Enabled on all switches in the network

D. Enabled on all interfaces of the switch

Which port security method converts existing dynamically learned MAC addresses on an interface to this mode and not age out?

A. Static

B. MAC address

C. Sticky

D. Dynamic

Which RSTP-PV features are embedded and cannot be disabled?

A. DirectLink Rapid Convergence and DirectLink Fast Rapid Convergence

B. InditectLink Rapid Convergence and IndirectLink Fast Rapid Convergence

C. DirectLink Rapid Convergence and IndirectLink Fast Rapid Convergence

D. DirectLink Fast Rapid Convergence and IndirectLink Rapid Convergence

What is the maximum number of dynamic MAC addresses that can be learned on a Dell EMC N-Series switchport that is configured for dynamic locking?

A. 100

B. 300

C. 400

D. 600

A network administrator is setting up a Class 5 powered device in their network. Which Dell EMC N-Serves switch model(s) will support this device?

A. N1100P and N2000P

B. N1500P

C. N2000 and N3000P

D. N3000P only

In order to alter a packet's routing direction, which packet layers can policy-based routing use?

A. Transport, Network, Link Layer, and Physical

B. Link Layer, Physical, Presentation, and Session

C. Network, Link Layer, Physical, and Session

D. Application, Transport, Network, and Link Layer

Which spanning tree feature will prevent unnecessary timeouts from DHCP servers?

A. PortFast

B. Loop Guard

C. BPDU Flooding

D. Root Guard