Refer to the exhibit.
An OSPF adjacency between Router-A and Router-B cannot reach the FULL state. Which action resolves the issue?
A. Adjust the MTU on Router-A to 1600.
B. Disable the check of the MTU value.
C. Set the OSPF media type to point-to-point.
D. Adjust the MTU on Router-B to 1604.
Refer to the exhibit.
vPC between switch1 and switch2 is not working. Which two actions are needed to fix the problem? (Choose two.)
A. Match vPC domain ID between the two devices.
B. Configure IP address on the interface.
C. Activate VLANs on the vPC.
D. Configure vPC peer link and vPC peer keepalive correctly.
E. Configure one of the switches as primary for the vPC.
Refer to the exhibit.
An engineer is troubleshooting why user1, user2, and user3 from group STORAGE-ADMINISTRATOR in Microsoft Active Directory cannot log in to the Cisco MDS SSH CLI. Which action resolves the issue?
A. Configure the role name to match the group name on Microsoft Active Directory.
B. Include specific users into MDS role configuration.
C. Configure SSH logins on Cisco MDS switch.
D. Integrate Cisco MDS with Microsoft Active Directory.
Refer to the exhibit.
After the configuration is performed, the Guest shell continues to use 2% CPU. Which action resolves the issue?
A. Resync the database
B. Recreate the guestshell
C. Reboot the guestshell
D. Reboot the switch
A network engineer must connect a Cisco UCS rcluster to the Cisco ACI. VMware ESXi hypervisors have been installed on Cisco UCS blades and a VMware VMM domain has been configured. However, virtual machines fail to reach their default gateway in the Cisco ACI Fabric. The engineer investigates the issue and notices that the VMware Distributed Switch (VDS) teaming policy is set to "Route based on IP hash". Which action resolves the issue?
A. Disable the VMware Network I/O Control on the VDS.
B. Configure the vSwitch Policy on a VDS.
C. Disable the On-demand EPG resolution immediacy setting in ACI.
D. Configure the vSwitch Policy on the VMM domain.
An engineer is recovering a fabric interconnect from a failed upgrade. The engineer booted the fabric interconnect to the switch(boot)# prompt and copied all the required images. Which image must be linked to nuova-sim-mgmtnsg.0.1.0.43404505131.bin to make the management image compliant with the Cisco UCS Manager?
A. Kickstart
B. System
C. UCS Manager
D. Cisco IMC
Refer to the exhibit.
The OTV overlay is deployed in multicast mode. After an unexpected reload of N7K-SITE1- OTV1, the network administrator observed that on N7K-SITE1-OTV2 the OTV site adjacency went into the partial state. Which action resolves the issue?
A. Change the Site-VLAN on N7K-SITE1-OTV2 to VLAN 1.
B. Enable IP IGMP version 3 on the join interface on N7K-SITE1-OTV1.
C. Configure the Site-Identifier on N7K-SITE1-OTV1 to 0002.0002.0002.
D. Modify the multicast data-group on N7K-SITE1-OTV1 to match N7K-SITE1-OTV2.
Refer to the exhibit.
An administrator directly connects a Fibre Channel storage array to ports 1 through 4 on a Cisco UCS 6454 Fabric Interconnect. The administrator configures a service profile to boot directly from the new Fibre Channel storage array, but the service profile fails to boot. When the administrator checks the output of the show flogi database command on the fabric interconnect, it shows the output presented in the exhibit. Which action resolves the issue?
A. Configure the Zoning Type in vHBA Initiator Group as Multiple Initiator Multiple Target.
B. Configure the fabric interconnects in Fibre Channel end-host mode.
C. Configure the Zoning Type in vHBA Initiator Group as Multiple Initiator Single Target.
D. Configuare the fabric interconnects in Fibre Channel switch mode.
Refer to the exhibit.
A switch fails to join the storage area network fabric in VSAN 6 where the fabric binding is enabled. Which configuration set resolves the issue?
A. Option A
B. Option B
C. Option C
D. Option D
DRAG DROP
Drag and drop the actions from the left onto the faults that they resolve on the right. Not all options are used.
Select and Place: