When editing a previously configured service policy, what options become available if you click the 'show advanced settings' checkbox? (Select 3)

A. Allows enabling/disabling the detection of dips in the metric.

B. Allows tuning of the tolerance range of the metric.

C. Allows setting of a noise floor for the metric.

D. Allows adjusting the notifications for the metric.

E. Allows enabling/disabling the detection of spikes in the metric.

Within Cascade Profiler you can set the recipient for policy notifications under Advanced configuration to:

A. Log Only, SNMP Only, Email Only, SNMP and Email

B. Log Only, Default, Owner, or any defined recipient

C. Log Only, Default, Owner or any User Account

D. Log Only, Default, Owner or any User Name obtained via the Identity Integration

What do you need to configure on the Profiler to detect utilization for an interface?

A. You have to manually configure the interface speeds on the Devices/Interfaces page.

B. You have to configure SNMP access to the reporting devices on the Devices/Interfaces page.

C. One of either A or B above.

D. None of the above; Cascade will figure this out automatically.

Within Cascade Pilot, Sequence Diagrams represent TCP Errors in which of the following ways: (Select 2)

A. By listing lost packets in the expert window

B. By using dotted-dashed lines for out-of-sequence segments

C. By placing error names on the messages within the diagram

D. By color-coding the messages on the diagram

E. By using a thicker line for messages that include errors

What are possible explanations for no Server Delay measurement being reported for a particular flow? (Select 4)

A. The flow includes the UDP protocol.

B. The traffic was not reported by a Cascade Sensor or Cascade Shark appliance.

C. The traffic was not reported by a Steelhead appliance's CascadeFlow

D. The start time for the connection was prior to the timeframe selected for the traffic query.

E. The packets involved in the initial setup of the TCP connection were not seen by a Cascade Sensor or Cascade Shark appliance.

On Cascade Profiler, can you run a traffic report that shows all traffic from inside the network to outside the network, but excludes a proxy server?

A. No, this cannot be done with Cascade.

B. Set up the query to ask for all hosts between: Hosts "Within" a group "ByInternalHosts: All" (where All is a host grouping containing all inside address space) and for Peers set to "Outside oF. ByInternalHosts:All".

C. Configure query as B above but also add the Proxy Server to the "Outside" list.

D. Configure query as B above but also add the Proxy Server as a "not" in the Traffic Expression field. The expression to add would be "not host proxyhost " where proxyhost is the IP Address of the proxy.

Time Control within Cascade Pilot is used for:

A. Controlling the portion of a packet capture (pcap) file analysed in the current view.

B. Creating a trace clip from a Cascade Shark appliance Capture job.

C. Controlling the size of a Capture Job created on a Cascade Shark appliance.

D. A and B

E. A, B, and C.

Cascade Shark can export flow data to a Cascade Profiler. When configuring Cascade Shark, flow export can be configured:

A. Per each capture job

B. Per each trace clip

C. Per each capture port

D. Per each capture board/aggregating port

E. Per each Cascade Shark appliance

NetFlow v9 uses the concept of templates. How do you tell the Cascade Gateway the proper template information?

A. You configure the NetFlow v9 template on the Gateway for each NetFlow v9 exporting device.

B. You manually import the NetFlow v9 template for each device.

C. The template is automatically learned by the Gateway.

D. All of the above.

E. None of the above.

Which is a true statement regarding choosing between a 2U and a 3U Cascade Shark base appliancE. (Select 2)

A. You must consider how many capture cards are required.

B. You must consider how much disk space is required.

C. You must consider the write-to-disk speed required.

D. You must consider how many Cascade Pilot consoles will be connecting.

E. You must consider how many Cascade Profilers the appliance will export to.